Plans for Six Drawer Emmerson Dresser

Plans

Dimensions

Lumber

• Two sheets of ¾" plywood
• one – 1×3 at 8'
• 1 – ane×vi at 3'
• 6 – 1×8 at viii'
• One sheet of ¼" plywood

Cut List

• 2 – i×half-dozen at 14" –Base of operations
• 1 – ¾" plywood at xviii" 10 52-3/4" – Bottom
• 2 – 1×3 at 47-1/four" – Base Stretchers
• 2 – ¾" plywood at eighteen" x 27-iii/4" – Sides
• 1 – ¾" plywood at 17-ane/4" x 27" – Divider
• iv – ¾" plywood at 17-1/iv" x 26" – Shelves
• ane – ¼" plywood at 27-3/4" ten 54-1/4"" – Back
• one – ¾" plywood at 18-1/4" x 54-1/4"" – Top
• 12 – ane×8 at 14-one/2" – Drawer Box
• 12 -1×8 at 25" – Drawer Box
• 6 – ¼" plywood at xvi" x 25" – Drawer Bottom
• 4 – ¾" plywood at eight-3/4" x 26-1/8" – Drawer Fronts
• 2 – ¾" plywood at 9" ten 26-i/eight" – Center Drawer Front

Instructions

Earlier beginning to build, always check in on my site to brand sure y'all have the most up to date gear up of plans, I occasionally update and modify the plans to make the edifice process easier or to allow for less expensive purchasing of materials! Read through the unabridged set up of instructions and all comments before beginning this projection. If you print out or save plans, exist sure to check in on my site to be certain you have the about up to date set up of plans, as I occasionally update things for ease of building or ownership. If you are new to building, read through the GETTING STARTED section and other manufactures plant nether the BUILD tab in the menu on my site, it has valuable data about how to get started, tools and techniques. If yous are unfamiliar with the finishing procedure, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use gum to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and information technology volition last for ages. Adhere to all safety standards and guidelines, and exist sure you follow safety protocol throughout your build. If you are unsure nearly whether y'all are edifice safely, run a quick online search for the tool or technique you are using, or contact me via email or mail to the forum before you move alee. My contact info can be found in the bill of fare of my site.

Step ane

Utilize optional edge banding to exposed edges of plywood before assembly.

Cut the pieces for the base and lesser. Set the Kreg jig for ¾" material and drill pocket holes in one long edge of each base piece. Also drill pocket holes in each end of the lesser to adhere the sides. Position the base pieces on the lesser as shown and adhere using gum and 1-1/4" pocket pigsty screws.

Cut the pieces for the base stretchers. Drill pocket holes in each terminate as well as one long edge of each slice. Adhere to the bottom and existing base of operations pieces using glue and 1-1/4" pocket hole screws.

Step 2

Cutting the pieces for the sides. Drill pocket holes in the top border of each slice to attach the acme. Attach to the lesser using glue and one-1/4" pocket hole screws.

Step 3

Cut the slice for the divider. Drill pocket holes in each of the shorter ends. Attach to the lesser equally shown using mucilage and i-1/4" pocket hole screws.

Stride 4

Cut the piece for the shelves. Drill pocket holes in each edge. Secure to the sides every bit shown using glue and 1-one/4" pocket hole screws. The shelves will be set ¾" dorsum from the front end edge of the sides.

Footstep 5

Cut the slice for the back and adhere using glue and 1-1/4" brad nails.

Cut the piece for the superlative. Attach to the sides using mucilage and 1-i/four" pocket hole screws.

Stride vii

Cut the pieces for the drawer boxes. Assemble as shown using glue and 1-1/4" pocket hole screws. Cutting the pieces for the drawer bottoms. Attach to the drawer boxes using glue and 1-1/iv" brad nails. Adhere the drawer slide hardware according to the manufacturer'due south instructions.

Step eight

Cut the pieces for the drawer fronts. There volition be a 1/8" gap all the way around. Align, employ shims to hold in identify if needed. Fasten using 1 one/4″ Brad Nails and mucilage from the front end. In one case the mucilage has prepare upwardly, adhere from the inside if you prefer using ane 1/4″ screws then attach the drawer pulls according to the manufacter instructions.

Finishing Instructions

Fill any Screw, Blast or Pocket Holes, Sand and Finish every bit Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private utilize only. Feel Free to link to whatever of my plans and then long every bit you lot provide an acceptable link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I promise to provide authentic plans, notwithstanding, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, and so you are building at your ain run a risk. It is recommended that you take a articulate understanding of how the project works before beginning any project. Delight contact me if you find an error or inaccuracy so that I might ready it.

heinsheizips.blogspot.com

Source: https://www.thedesignconfidential.com/2013/08/free-diy-furniture-plans-build-emmerson-6-drawer-dresser/

Share this post